Griffon Poly Max 6150452 Fix & Seal Express sealant 290ml crystal clear! (Crystal Clear)

Griffon Poly Max sealant

POLY ^MAX® FIX & SEAL EXPRESS

TUBE 300 G CRYSTAL CLEAR SOLVENT-FREE ASSEMBLY ADHESIVE AND SEALANT WITH VERY HIGH ELASTICITY AND VERY FAST STRENGTH BUILD-UP BASED ON SMP POLYMER. IDEAL FOR MOUNTING IN COMBINATION WITH SEALING.

Field of application
For bonding and mounting many building materials on almost all substrates, such as wood, (natural) stone, (gas) concrete, metal, hard foam and various plastics. Suitable for indoor and outdoor applications such as battens, skirting boards, skirting boards, window sills, board and insulation materials. Also suitable for sealing joints, seams and cracks in (plastic) frames, fascias, roofs, gutters, walls, skylights and chimneys. For all professional applications, such as facade and interior construction, housing, utility and bodywork construction.

Properties
*Very high, permanent elasticity
*Very fast strength build-up
*Very good filling capacity
*Good standing ability
*Shrink-free; 100% adhesive
*Solvent-free
*No edge zone contamination
*Weatherproof
*Temperature resistant from -40°C to +100°C
*Paintable
*Curing time approx. 2 mm/24 hours

Processing
Preparation
Processing conditions: The temperature of environment, adhesive and materials to be bonded should not be lower than +5°C.
Pretreatment surfaces: Surfaces must be clean, dust- and grease-free. Provide a firm substrate. Substrate may be slightly moist. Use of primer not necessary.
Tools: caulking gun and rubber mallet.

Processing
Consumption: For dotwise bonding: 5-8 m²/kg. Striping: from 1 tube comes approx. 8-15 meters of adhesive (depending on diameter cut-off nozzle).
Instructions for use:
-Adhesives/MOUNTING: Cut thread, assemble nozzle and cut to a diameter of min. 0.5 cm. Apply adhesive evenly, depending on the weight of the material, every 10 to 40 cm in vertical stripes or dots. Always apply adhesive at corners and along edges. Mount materials directly with a sliding movement and press or tap firmly. Corrections are still possible. With heavy materials fixate or support if necessary. After use, immediately close the tube tightly.
-Sealing: Cut off the thread, fit the nozzle and cut at an angle to the desired joint width. Apply sealant to the bottom of the joint and smooth out within 10 minutes with a wet (water with detergent without lemon) finger, putty knife or sealant spreader. Smooth vertical joints from bottom to top. Close tube tightly immediately after use.
Stains/Residue: Remove wet adhesive residues immediately with white spirit. Dried adhesive residues can only be removed mechanically.
Points of attention: The following drying times are based on the bonding of at least one porous material and an adhesive layer with a thickness of approx. 1 mm. When bonding two non-porous materials and/or a thicker adhesive layer, considerably longer drying times must be taken into account.

Drying times
* Skin-forming time: approx. 30 minutes
* Hand-holding time: approx. 1.5 hours
* Curing speed: approx. 2 mm/24 hours
* Final strength: maximum final strength is achieved after approx. 4 hours
Drying times may vary depending on, among other things, substrate, amount of product applied, moisture content and ambient temperature.

Technical properties
Moisture resistance: Very good
Water resistance: Good
Temperature resistance: From -40°C to +100°C
UV resistance: Good
Resistance to chemicals: Good
Paintability: Can be painted with both acrylic and alkyd paints. Drying delay may occur with alkyd paints. Always test in advance.
Elasticity: Very good
Filling capacity: Very good

Technical specifications
Basic material: SMP polymer
Color: Crystal Clear
Viscosity: Pasty
Solid content: approx. 100
Density: approx. 1.04 g/cm³
Tensile strength: approx. 210 N/cm²
Shear strength: approx. 290 N/cm²
Flash point: K3 (>55°C)
Shrinkage: approx. 0
Hardness (Shore A): approx. 45
Elasticity E-modulus: approx. 0.9 MPa
Elongation at break: approx. 250

Storage conditions
Minimum 18 months. Best Before Date (MM/YYY): see packaging. Opened packaging has a limited shelf life. Store dry in closed packaging between +5°C and +25°C.